• 6,000 - 8,000 lbs. Lifting Capacity
  • 96" Forks Option
  • AC-Powered
  • Length to forkface 76.4 - 186.8 in
  • Height (Extended Handle) 56.7 in
  • Overall Width 36 in

The Toyota End-Controlled Rider pallet jack is easy to maneuver and quick to respond to commands. The End-Controlled Rider, ideal for longer runs, makes moving product throughout the warehouse efficient and enjoyable. Doubling as a ground-level order picker, the End-Controlled Rider pallet jack is an asset to any warehouse or distribution center.


  • Multifunction control handle with ergonomically angled hand grips
  • Dual thumb wheels with twist grips for directional control and travel speed
  • High-speed interlock
  • Fingertip control of lift, lower and horn functions
  • Curvilinear hand rail contoured and cushioned for a natural, comfortable feel
  • Low-effort control handle
  • Soft-cushioned rider platform
  • Low platform step height


  • 6,000 & 8,000 lb capacity
  • 24-Volt electrical system
  • 6? lift
  • AC Drive System with thermal protection and current limiting
  • Fault code memory with hour meter reading
  • Regenerative braking
  • Programmable performance parameters
  • Multiple hour meter indicator
  • Battery discharge indicator with lift interrupt
  • Fused control and power circuits
  • On/off key switch
  • Lift limit switch
  • Hydraulic overload protection valve
  • Dual lift cylinder design
  • Drive-thru freezer curtain feature


  • AC drive motor (no brushes or commutator)
  • One-piece, lightweight service access cover
  • Teflon coated polylube lift linkage bushings (maintenance free)
  • Error indicator with self-diagnostics


  • Stability hand rail with lift, lower, horn and high-speed functions
  • Wrap-around hand guard
  • Spring-loaded control handle
  • Directional reverse switch on control handle
  • Runaway protection
  • Polyurethane torsion block stabilizing casters (only standard on 84? fork length.)
  • Electronic horn


  • Controller Area Network (CAN-bus) communications
  • Welded construction with reinforced heavy-duty bumper
  • Powder-coat paint finish
  • Box rail fork construction
  • Steel gusset reinforced rider platform
  • Steel bulkhead wrappers
  • Forged rectangular steel tension rods
  • Heavy-duty bushings and pins
  • Solid trail fork castings
  • Tapered fork tips with pallet entry slides
  • Four-point lift linkage
  • High-strength polymer service cover
  • Fiberglass reinforced rubber drive tire
  • Polyurethane load wheels with steel hubs
  • Hall-effect switches


  • Galvanized Chassis Suited for customers who move materials in and out of: cold storage facilities; chemical and salt and brine industries; or in areas where frequent wash down is required to remove contaminants.
  • Battery Compartment Rollers with Dual Side Gates Option provides rollers at the bottom of the battery compartment and dual side gates. Allows the battery to be rolled out from either right or left hand side of the truck.
  • Pallet Entry/Exit Rollers Option replaces the standard pallet entry/exit slides with durable hard polymer pallet entry/exit rollers.
  • Dual Tandem Load Wheels (3.25" x 2") Option replaces the standard single polyurethane load wheels with "Double Boggie" style load wheels.
  • Battery Side Gate Interlock Switches Option helps warn the operator if either left or right hand side battery side gate is left open.
  • Storage Tray with Clip Board, Load Backrest Mounted An ABS plastic tray designed to carry pens, markers, tape, utility knife, paperwork and other various work materials.
  • Lubrication Package For Pivot Points (Grease Fittings) Option replaces the standard maintenance free Teflon® coated Polylube™ bushings at the lift linkage pivot points with greaseable bushings (grease fittings).


Model Number Load Capacity* (lbs.) Max. Travel Speed Full Load (MPH) Max. Lift Speed Full Load (FPM) Max. Gradeability Full Load (%) Basic Right Angle Stack** (IN.)
8HBE30 6,000 6.2 N/A 10 85.4
8HBE40 8,000 6.2 N/A 10 129.3

* Based on 24" load center.
** Add load length and clearance.